Our billet aluminum solid shifter bushings, these bushings provide an increased feel in shifting performance.  Replace your worn out rubber bushings on your shift linkage to shifter to increase the feeling in the shifter.  These come with a pair of solid bushings, o-rings and the correct prevailing torque nut.  This will fit both F and H series shifter cables.

*Be sure to check your shifter to ensure our solid bushings fit over the mounting stud.  The mounting hole in the bushing is an M6.  

Our billet aluminum block off plates is designed to fill the hole left in your firewall after performing a wire tuck or just relocating a few items.  In this set you will receive the following:

Our billet aluminum block off plate is designed to fill the hole left in your firewall on the passenger side under the fuse box.  Our FFC logo is etched into the front plate.  Each piece comes with a front and back plate and all hardware is included.

Our small billet aluminum block off plate fits the hole where the A/C is located and also the main harness plug on the drivers side.  Our FFC logo is etched into the front plate.  Each piece comes with a front and back plate and all hardware in included.  If you need to plug both holes in firewall, please be sure to order 2.  Price below is for one front and back plate along with the hardware.





Our billet aluminum package includes the following:

• one pair of aluminum lower control arms
• one pair of aluminum toe arms
• FFC ABS relocation brackets
• bushing grease

Product description: The perfect match to our billet aluminum lower control arms.  We designed our billet aluminum tow arms to complete the package.  We are the only company that offers both lower control arms in billet aluminum.  They are milled just like our lower control arms from a solid piece of 6061 aluminum and feature our standard triangle cuts with our FFC logo etched in the middle.  The installed bushings are Prothane and come with bushing grease.

Product description:  Our lower control arms are the only arms on the market that are not driver or passenger side specific.  We were able to design our lower control arms to provide more clearance without adding additional bends.  Our design offers the most clearance when you want to be low.  With the factory design when you lower your Accord the lower control arm on the passenger side is now actually closer to the frame of your car.  With our lower controls arms installed when you lower your Accord we actually provide additional clearance because of our design. 

Our Lower control arms are milled from a solid piece of 6061 billet aluminum.  We use Prothane polyurethane bushings.  We choose them so our customers could easily replace the bushings if needed.  Our lower control arms feature our standard triangle cutouts with our FFC logo etched in the middle.  We provide bushing grease and ABS relocation brackets and hardware with each purchase.

Our extended top hats are made from a solid piece of 6061 billet aluminum.  Our top hats will provide you with an additional 1.25 inches of shock travel that is normally lost when lowering your car.  The top hats will come with all new mounting hardware (pre installed), spring isolator bushings and strut rod bushings.  You will reuse your bumpstop and bushing sleeve. 

They are designed to work with all shocks and sleeved coilovers.  They will also work most coilovers that use a 2.5 inch diameter spring that did not come with a replacement top hat.  If you have any questions if they will fit your coilover, please contact FFC before you order. Be sure to also check your strut bar mounting brackets.  Some strut bar brackets may not provide enough clearance for the added height of our top hats.

INSTALLATION INSTRUCTIONS

Product Description:

Our unique brake caliper bracket design is milled from a solid piece of 6061 billet aluminum.  Our brake caliper bracket allows you to use the 2005+ RL brake calipers on your Accord.  We designed our brackets so that all the mounting holes are centered on the block of aluminum.  By doing this, it ensures that equal stress is being put on both sides.  We also made sure that the caliper is centered around the rotor, which allows the caliper to create equal pressure on each side when the brakes are applied.  All mounting hardware is included with your bracket purchase. The mounting holes where the bracket is mounted to the knuckle are 5 ½ inches apart.

On our test vehicles we used 2006 350Z rotors* equipped with Brembo calipers.  PLEASE BE SURE THIS WILL CLEAR YOUR WHEEL SET UP BEFORE PLACING YOUR ORDER, YOU MUST HAVE A 17 INCH OR LARGER WHEEL.

INSTALLATION INSTRUCTIONS

*buyer to supply their own brake calipers, brake rotors and brake pads



This package includes the following FFC products:

• (1) pair of billet aluminum radiator brackets
• (1) billet aluminum battery tie
• (1) set of our billet aluminum fender washers (20 pieces)

 All necessary mounting hardware is included.  You will reuse your factory battery tie down "j" hooks.

Product description: Looking for a part that will show that you have paid attention to the details in your build?  Look no further than our billet aluminum fender washers.  Our fender washers can be used anywhere there is a 10mm bolt that you want to dress up.  These are milled from 7075 aluminum and add a touch of class wherever they are installed.  These come with the all necessary hardware.   

Product description: Looking for a part that will show that you have paid attention to the details in your build?  Look no further than our billet aluminum fender washers.  Our fender washers can be used anywhere there is a 10mm bolt that you want to dress up.  These are milled from 7075 aluminum and add a touch of class wherever they are installed.  These come with the all necessary hardware. 

Product description: Our FFC battery tie down is milled from a solid piece of 6061 billet aluminum.  The flat bottom design allows for our battery tie to work with many OEM or aftermarket batteries on the market.  The lip on each end tie down allows for your battery to be held securely in place.  Our battery tie down showcases our FFC logo within the triangle cutouts.  The billet aluminum battery tie is a great additional to any engine bay.  The mounting holes are 7 15/16”apart.